Your Frymaster fryer keeps up with the cooking rush day after day without needing attention. Until one day an error code that you haven't encountered before appears on the display.
Some Frymaster fryer error codes aren’t disastrous at all and just warn about casual things like a dirty filter pad (E21). In this guide, we’ve gathered the most typical fault codes for major controllers.
Some suggest you can take a few troubleshooting steps, while others may indicate the equipment failure just happened and you need the right Frymaster parts to restore that reliable performance you’ve come to expect from your equipment.

Jump to:
E03: Temperature Probe Failure
This is one of the most typical error codes among the faults that require serious attention. It means the temperature probe reading is out of the acceptable range due to a failed probe itself, loose or broken wiring, or in some cases the controller board may have a fault.
Troubleshooting:
1. Power down the fryer and let it cool completely.
2. Inspect the probe wiring harness and connector for corrosion, loose pins, or visible damage.
3. If connections look good, test the probe resistance (should read approximately 1,080 ohms at 70°F for a standard RTD probe).
4. If the probe is reading out of range, it needs to be replaced.
E05: High Temperature Warning
Consider this a red-alert code. E05 means the high-limit temperature has exceeded 410°F (210°C) or 394°F in CE-compliant markets. At that point, the oil is almost certainly beyond usable quality and may be a fire hazard.
What to do:
1. Shut the fryer down immediately. Do not attempt to continue cooking.
2. Do not try to move or drain the oil while it is at this temperature.
3. Let everything cool fully before inspecting the system.
4. Call a service technician. The root of the error could be a failed temperature probe sending incorrect readings to the controller, a stuck contactor, or a failed high-limit thermostat.
E06: Heating Failure
If your fryer won’t heat up, this is one of the error codes it may display. It means a component in the heating circuit has failed and depending on your fryer model, be it gas or electric, the range of components causing this may include anything from a controller to an open high-limit switch.
Troubleshooting:
1. Verify if the drain valve is fully closed. If partially or fully open, it could trigger a heating failure on some models.
2. Verify the high-limit switch hasn’t tripped. Reset if so. If it trips again immediately, call a tech as the problem sits deeper.
3. The checks that follow require a technician to test the gas valve, ignition module, contactor, and control board in sequence.
E09: Pump Not Filling
This code appears when it takes too long for oil to flow from the filter pan back into the frypot. This could be due to a clogged or collapsed filter pad, a bypassed filter pad, or a filter pump that’s nearing the end of its service life.
What you can do to possibly fix it:
1. Stop the filtration cycle.
2. Drain and cool the oil. Remove and inspect the filter pad. A heavily darkened, collapsed, or saturated pad is the most likely cause.
3. Replace the filter pad and make sure it’s seated flat and flush in the pan.
4. If a fresh pad doesn’t resolve it, check that the bypass valve, if your model has one, is fully closed.
5. If the pump motor hums briefly and then stops, there may be a blockage in the pump itself, which requires a service call.
Regular filter pump maintenance goes a long way toward keeping E09 from appearing. Replace the filter pad on schedule - daily according to the documentation for most models, and chances are high you’ll rarely see this code.
E21: Filter Pad Procedure Error / Change Filter Pad
This is a maintenance reminder, not a dreaded mechanical failure. It appears either when the 25-hour filter pad timer has expired or when the fryer’s dirty filter detector has detected the pad needs changing based on frying volume and conditions.
The fix is easy: change the filter pad and follow the on-screen prompts to reset the timer. If the code keeps coming back sooner than expected, you may be frying at a higher volume than your filter maintenance schedule accounts for, so try increasing your change frequency.
Quick Reference: Frymaster Error Codes at a Glance
| Error Code | Display Message | What It Means |
| E01 | REMOVE DISCARD (Right) | Setpoint mismatch — right vat |
| E02 | REMOVE DISCARD (Left) | Setpoint mismatch — left vat |
| E03 | TEMP PROBE FAILURE | Temperature probe out of range |
| E04 | HI 2 BAD | High-limit sensor out of range |
| E05 | HOT HI 1 | Oil temp exceeded 410°F — shut down immediately |
| E06 | HEATING FAILURE | Component failure in heating circuit |
| E09 | PUMP NOT FILLING | Dirty filter pad or pump issue |
| E10 | DRAIN VALVE NOT OPEN | Drain valve failed to open |
| E11 | DRAIN VALVE NOT CLOSED | Drain valve failed to close |
| E21 | CHANGE FILTER PAD | Filter pad timer expired |
| E22 | OIL IN PAN ERROR | Oil detected in filter pan |
| E25 | RECOVERY FAULT | Oil temp recovery exceeded time limit |
| PROB (CM III.5) | — | Probe or controller failure |
| HOT (CM III.5) | — | Extreme overtemperature |
| HELP (CM III.5) | — | Heating problem |
- Behind the Science of Modern Skincare: How Research Labs Study Bioactive Peptides in Cell-Culture Models
- What Are the Key Steps for Starting ABA Therapy in Maryland for Autism?
- A Busy Family’s Guide to Keeping the Plumbing Happy
- How to Grow a Home-Based Business Without Putting Your Family Budget at Risk
The Bottom Line
Frymaster fryers are built to be durable and provide worry-free operation, so on-screen error messages don't always mean a major breakdown.
But certainly they aren't something to ignore. If a simple maintenance check is all it takes to get your fryer running again, that’s great.
Other times, the problem calls for replacement parts or professional repair.
Check the error code in your fryer's model-specific manual, and if a component needs replacing, make sure you're getting compatible Frymaster parts to get your equipment back in service.










Leave a Reply