This Lavender Goat Milk Soap Recipe is a fantastic recipe for homemade soap. In fact I love the smell of Lavender. It’s such a fantastic smell and can be very relaxing and therapeutic for the body.
Goats Milk Soap is fantastic for giving the body a smooth and silk feel and I know you’ll love this recipe.
*I use affiliate links in this post. If you buy anything from my links I will earn a small commission*
Ingredients Needed For Lavender Goat Milk Soap
106 ounces tallow
14 ounces lye
41 ounces cold water
9 ounces goat milk
2 teaspoons lavender essential oil
How To Make DIY Lavender Goat Milk Soap
Place the correct amount of lye into a plastic pitcher.
Be sure to weigh this by placing the container on a scale, making sure it is set to zero and then adding the lye. This step is very important!
Set the pitcher containing the lye aside someplace where it will not get knocked over.
Now using the same method, place a second plastic pitcher on the scale and weigh the cold water.
Carefully pour the water into the pitcher containing the lye.
Do this slowly and be sure you are wearing your soap making safety equipment such as rubber gloves and safety glasses.
Do not splash this mixture!
Once all of the water is in the pitcher containing the lye, stir the mixture with a wooden spoon, again taking care to not splash the mixture.
Continue stirring the lye mixture until all of it is dissolved.
At this point, the lye mixture should have heated up and have reached a temperature somewhere between 150 degrees Fahrenheit to 200 degrees Fahrenheit.
Set the pitcher containing the lye mixture aside to cool. Again, be sure it is in a safe place so it does not accidentally get knocked over.
You want the lye to cool down so the temperature is 100 degrees Fahrenheit.
You can use a hot or cool water bath to help the process along.
Now go ahead and weigh the tallow and place it in a stainless steel pot or an enamel pot without chips in it.
Set the pot on the heat source and set the heat temperature to medium to melt the tallow.
Stir the contents frequently to encourage the melting process. It is ok to smash the small pieces against the side of the pot to encourage them to melt.
Once the tallow is melted, stir continually to reduce the temperature to 105 degrees Fahrenheit.
You can use a cold water bath to lower the temperature faster.
Double and triple check the temperature of both the lye solution and the tallow.
This is a very important step! Both the tallow and lye needs to be in the 95 degrees Fahrenheit and 100 degrees Fahrenheit range!
Be sure you still have your rubber gloves and safety glasses on before proceeding to the next step.
Begin stirring the tallow and slowly – very slowly – pour the lye solution into the pot with the tallow while continuing to stir the mixture.
The only way to get the lye to absorb into the fat is to keep stirring it. This is a long process!
Stir gently so you do not splash the contents out of the pan.
The mixture will begin to thicken and turn opaque. It will look grainy instead of smooth. This is normal.
Continue to stir until you see trailings, which are lines of soap that float on the surface yet remains distinct from the soap in the pot.
To test for this, lift your spoon out of the pot and drizzle a thread of soap on top of the mixture.
If you see the distinct markings of the drizzle on the surface the soap has reached the trailings stage.
At this point, simply pour your soap into the mould, place a lid on the mould and wrap the entire mould in old towels to insulate it.
Place the mould in a warm place where it will not be disturbed for 48 hours.
After 48 hours have passed, unwrap the soap, but do not touch it without wearing the rubber gloves. It is still caustic.
The soap should be solid looking but may still be soft to the touch.
Leave the soap uncovered for another 48 hours, then see if it is hard enough to touch without leaving an impression, if it proceeds, if not, then allow it to harden a little longer.
Once the soap is hard enough, then turn the mould upside down over a sink or inside a tub and press the bottom to release the soap from the mould.
If the soap does not easily release, set it aside and give it a couple more days to dry.
Once the soap is out of the mould, place it on a clean surface with a piece of freezer paper underneath it.
Allow it to sit exposed to the air for a week to harden more.
Now it is ready to be cut into bars of soap. These bars can be any size you desire them to be.
A knife warmed with hot water will cut into the bars of soap easily.
Once the soap is cut into bars, it needs to dry for another two weeks.*
Be sure to place the bars of soap on freezer paper to dry.
Once the bars of soap are done curing, grate the soap.
This is easily done with an electric kitchen grater but it can be done by hand if you prefer.
Place 12 ounces of grated soap into a stainless steel pan.
Add 9 ounces of goat milk soap to the grated soap.
Place the pan on the heat source and turn it to medium.
Stir the mixture continually until the soap is melted.
Allow the soap to cool just slightly, then add the 2 teaspoons of lavender essential oil and stir to mix the essential oil into the soap.
Pour the soap into the moulds.
If any bubbles form on top of the soap, give the soap a light spray of isopropyl alcohol. This will take care of the bubbles.
Allow the soap to cool and fully harden in the moulds.
Once the soap is hard, remove it from the moulds using the same process as above.
Set the moulded soap on freezer paper and allow it to cure. As stated above, I like to cure mine for a minimum of six months, but you can certainly use it after two weeks curing time if you prefer.
You May Also Enjoy The Following:
About Angela Milnes
Angela Milnes is a Qualified Early Years Teacher who has specialised in Preschool and Kindergarten teaching. She has a wealth of experience teaching young children and is passionate about kids crafts and having fun as a family. Angela has also taught cooking skills and loves to share both family recipes and easy instant pot recipes here on The Inspiration Edit. Follow her on Pinterest!